--------------------------------------------- * The following section contains information about your system Sat Jul 14 18:39:35 CEST 2001 Output of uname -a Linux meister 2.2.14 #28 Sat Jul 14 13:38:06 CEST 2001 i686 unknown --------------------------------------------- * The following section contains information about your network * interfaces. The one you chose for PPPoE should contain the words: * 'UP' and 'RUNNING'. If it does not, you probably have an Ethernet * driver problem. Output of ifconfig -a eth0 Link encap:Ethernet HWaddr 52:54:05:C5:05:2B inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:9 Base address:0xb800 eth1 Link encap:Ethernet HWaddr 00:80:48:C3:43:18 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:55 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:10 Base address:0xb400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:3924 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:30 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 ppp0 Link encap:Point-to-Point Protocol POINTOPOINT NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 --------------------------------------------- * The following section contains information about kernel modules * If the module for your Ethernet card is 'tulip', you might * want to look for an updated version at http://www.scyld.com Output of lsmod Module Size Used by ppp 20908 0 (autoclean) slhc 4440 0 (autoclean) [ppp] usb-uhci 17000 0 (unused) usbcore 42344 1 [usb-uhci] ne2k-pci 4232 2 (autoclean) 8390 6228 0 (autoclean) [ne2k-pci] serial 18516 0 (autoclean) nls_iso8859-1 2268 6 (autoclean) --------------------------------------------- * The following section lists your routing table. * If you have an entry which starts with '0.0.0.0', you probably * have defined a default route and gateway, and pppd will * not create a default route using your ISP. Try getting * rid of this route. Output of netstat -n -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 --------------------------------------------- Contents of /etc/resolv.conf * The following section lists DNS setup. * If you can browse by IP address, but not name, suspect * a DNS problem. nameserver 212.185.253.9 nameserver 194.25.2.129 --------------------------------------------- * The following section lists /etc/ppp/options. * You should have NOTHING in that file. Contents of /etc/ppp/options --------------------------------------------- * The following section identifies your Ethernet interface * and user name. Some ISP's need 'username'; others * need 'username@isp.com'. Try both ETH=eth1; USER=xxxxxxxxxxxxxxxxxxxxxxxxxxxx@t-online.de --------------------------------------------- * The following section shows the pppd command we will invoke pppd invocation /usr/bin/setsid /usr/sbin/pppd pty '/usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 ' noipdefault noauth default-asyncmap defaultroute hide-password nodetach mtu 1492 mru 1492 noaccomp noccp nobsdcomp nodeflate nopcomp novj novjccomp user xxxxxxxxxxxxxxxxxxxxxxxxxxxx@t-online.de lcp-echo-interval 20 lcp-echo-failure 3 debug --------------------------------------------- Using interface ppp0 Connect: ppp0 <--> /dev/ttyp2 sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] sent [LCP ConfReq id=0x1 ] LCP: timeout sending Config-Requests Connection terminated. Waiting for 1 child processes... script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-718/pppoe-debug.txt-0, pid 781 pppoe: Timeout waiting for PADO packets Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-718/pppoe-debug.txt-0 finished (pid 781), status = 0x100 --------------------------------------------- * The following section is an extract from your log. * Look for error messages from pppd, such as * a lack of kernel support for PPP, authentication failure * etc. Extract from /var/log/messages Jul 14 13:57:25 chef pppoe[710]: Timeout waiting for PADO packets Jul 14 13:57:25 chef pppd[709]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 finished (pid 710), status = 0x100 Jul 14 13:57:25 chef pppd[709]: Exit. Jul 14 14:02:53 chef pppd[803]: pppd 2.3.11 started by root, uid 0 Jul 14 14:02:53 chef pppd[803]: Using interface ppp0 Jul 14 14:02:53 chef pppd[803]: Connect: ppp0 <--> /dev/pts/2 Jul 14 14:02:54 chef pppd[803]: sent [LCP ConfReq id=0x1 ] Jul 14 14:03:24 chef pppd[803]: LCP: timeout sending Config-Requests Jul 14 14:03:24 chef pppd[803]: Connection terminated. Jul 14 14:03:24 chef pppd[803]: Waiting for 1 child processes... Jul 14 14:03:24 chef pppd[803]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 , pid 804 Jul 14 14:03:28 chef pppoe[804]: Timeout waiting for PADO packets Jul 14 14:03:28 chef pppd[803]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 finished (pid 804), status = 0x100 Jul 14 14:03:28 chef pppd[803]: Exit. Jul 14 14:03:52 chef pppd[852]: pppd 2.3.11 started by root, uid 0 Jul 14 14:03:52 chef pppd[852]: Using interface ppp0 Jul 14 14:03:52 chef pppd[852]: Connect: ppp0 <--> /dev/pts/2 Jul 14 14:03:53 chef pppd[852]: sent [LCP ConfReq id=0x1 ] Jul 14 14:04:23 chef pppd[852]: LCP: timeout sending Config-Requests Jul 14 14:04:23 chef pppd[852]: Connection terminated. Jul 14 14:04:23 chef pppd[852]: Waiting for 1 child processes... Jul 14 14:04:23 chef pppd[852]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 , pid 853 Jul 14 14:04:27 chef pppoe[853]: Timeout waiting for PADO packets Jul 14 14:04:27 chef pppd[852]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 finished (pid 853), status = 0x100 Jul 14 14:04:27 chef pppd[852]: Exit. Jul 14 14:04:32 chef pppd[913]: pppd 2.3.11 started by root, uid 0 Jul 14 14:04:32 chef pppd[913]: Using interface ppp0 Jul 14 14:04:32 chef pppd[913]: Connect: ppp0 <--> /dev/pts/2 Jul 14 14:04:33 chef pppd[913]: sent [LCP ConfReq id=0x1 ] Jul 14 14:05:03 chef pppd[913]: LCP: timeout sending Config-Requests Jul 14 14:05:03 chef pppd[913]: Connection terminated. Jul 14 14:05:03 chef pppd[913]: Waiting for 1 child processes... Jul 14 14:05:03 chef pppd[913]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 , pid 914 Jul 14 14:05:07 chef pppoe[914]: Timeout waiting for PADO packets Jul 14 14:05:07 chef pppd[913]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 finished (pid 914), status = 0x100 Jul 14 14:05:07 chef pppd[913]: Exit. Jul 14 16:46:53 chef kernel: registered device ppp0 Jul 14 16:46:53 chef pppd[590]: pppd 2.3.11 started by root, uid 0 Jul 14 16:46:53 chef pppd[590]: Using interface ppp0 Jul 14 16:46:53 chef pppd[590]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 16:46:54 chef pppd[590]: sent [LCP ConfReq id=0x1 ] Jul 14 16:47:24 chef pppd[590]: LCP: timeout sending Config-Requests Jul 14 16:47:24 chef pppd[590]: Connection terminated. Jul 14 16:47:24 chef pppd[590]: Waiting for 1 child processes... Jul 14 16:47:24 chef pppd[590]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 , pid 594 Jul 14 16:47:28 chef pppoe[594]: Timeout waiting for PADO packets Jul 14 16:47:28 chef pppd[590]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 finished (pid 594), status = 0x100 Jul 14 16:47:28 chef pppd[590]: Exit. Jul 14 16:47:33 chef pppd[653]: pppd 2.3.11 started by root, uid 0 Jul 14 16:47:33 chef pppd[653]: Using interface ppp0 Jul 14 16:47:33 chef pppd[653]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 16:47:34 chef pppd[653]: sent [LCP ConfReq id=0x1 ] Jul 14 16:48:04 chef pppd[653]: LCP: timeout sending Config-Requests Jul 14 16:48:04 chef pppd[653]: Connection terminated. Jul 14 16:48:04 chef pppd[653]: Waiting for 1 child processes... Jul 14 16:48:04 chef pppd[653]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 , pid 655 Jul 14 16:48:08 chef pppoe[655]: Timeout waiting for PADO packets Jul 14 16:48:08 chef pppd[653]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 finished (pid 655), status = 0x100 Jul 14 16:48:08 chef pppd[653]: Exit. Jul 14 18:00:59 chef kernel: registered device ppp0 Jul 14 18:00:59 chef pppd[626]: pppd 2.3.11 started by root, uid 0 Jul 14 18:00:59 chef pppd[626]: Using interface ppp0 Jul 14 18:00:59 chef pppd[626]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 18:01:00 chef pppd[626]: sent [LCP ConfReq id=0x1 ] Jul 14 18:01:30 chef pppd[626]: LCP: timeout sending Config-Requests Jul 14 18:01:30 chef pppd[626]: Connection terminated. Jul 14 18:01:30 chef pppd[626]: Waiting for 1 child processes... Jul 14 18:01:30 chef pppd[626]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-565/pppoe-debug.txt-0, pid 630 Jul 14 18:01:34 chef pppoe[630]: Timeout waiting for PADO packets Jul 14 18:01:34 chef pppd[626]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-565/pppoe-debug.txt-0 finished (pid 630), status = 0x100 Jul 14 18:01:34 chef pppd[626]: Exit. Jul 14 18:01:44 chef pppd[699]: pppd 2.3.11 started by root, uid 0 Jul 14 18:01:44 chef pppd[699]: Using interface ppp0 Jul 14 18:01:45 chef pppd[699]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 18:01:45 chef pppoe[701]: ioctl(SIOCGIFHWADDR): No such device Jul 14 18:01:45 chef pppd[699]: sent [LCP ConfReq id=0x1 ] Jul 14 18:01:45 chef pppd[699]: write: warning: Input/output error (5) Jul 14 18:01:45 chef pppd[699]: Modem hangup Jul 14 18:01:45 chef pppd[699]: Connection terminated. Jul 14 18:01:45 chef pppd[699]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I echo -T 80 -U -m 1412 -D /tmp/pppoe-debug-636/pppoe-debug.txt-0 finished (pid 701), status = 0x100 Jul 14 18:01:45 chef pppd[699]: Exit. Jul 14 18:02:02 chef pppd[769]: pppd 2.3.11 started by root, uid 0 Jul 14 18:02:02 chef pppd[769]: Using interface ppp0 Jul 14 18:02:02 chef pppd[769]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 18:02:03 chef pppd[769]: sent [LCP ConfReq id=0x1 ] Jul 14 18:02:33 chef pppd[769]: LCP: timeout sending Config-Requests Jul 14 18:02:33 chef pppd[769]: Connection terminated. Jul 14 18:02:33 chef pppd[769]: Waiting for 1 child processes... Jul 14 18:02:33 chef pppd[769]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-708/pppoe-debug.txt-0, pid 771 Jul 14 18:02:37 chef pppoe[771]: Timeout waiting for PADO packets Jul 14 18:02:37 chef pppd[769]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-708/pppoe-debug.txt-0 finished (pid 771), status = 0x100 Jul 14 18:02:37 chef pppd[769]: Exit. Jul 14 18:10:10 chef pppd[1802]: pppd 2.3.11 started by root, uid 0 Jul 14 18:10:10 chef pppd[1802]: Using interface ppp0 Jul 14 18:10:10 chef pppd[1802]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 18:10:14 chef pppd[1853]: pppd 2.3.11 started by root, uid 0 Jul 14 18:10:14 chef kernel: registered device ppp1 Jul 14 18:10:14 chef pppd[1853]: Using interface ppp1 Jul 14 18:10:14 chef pppd[1853]: Connect: ppp1 <--> /dev/ttyp3 Jul 14 18:10:35 chef pppd[1941]: pppd 2.3.11 started by root, uid 0 Jul 14 18:10:35 chef kernel: registered device ppp2 Jul 14 18:10:35 chef pppd[1941]: Using interface ppp2 Jul 14 18:10:35 chef pppd[1941]: Connect: ppp2 <--> /dev/ttyp4 Jul 14 18:10:36 chef pppd[1941]: sent [LCP ConfReq id=0x1 ] Jul 14 18:10:39 chef pppd[1941]: sent [LCP ConfReq id=0x1 ] Jul 14 18:10:41 chef pppd[1802]: LCP: timeout sending Config-Requests Jul 14 18:10:41 chef pppd[1802]: Connection terminated. Jul 14 18:10:42 chef pppd[1941]: sent [LCP ConfReq id=0x1 ] Jul 14 18:10:45 chef pppoe[1826]: Timeout waiting for PADO packets Jul 14 18:10:45 chef pppd[1802]: Exit. Jul 14 18:10:45 chef pppd[1941]: sent [LCP ConfReq id=0x1 ] Jul 14 18:10:45 chef pppd[1853]: LCP: timeout sending Config-Requests Jul 14 18:10:45 chef pppd[1853]: Connection terminated. Jul 14 18:10:48 chef pppd[1941]: sent [LCP ConfReq id=0x1 ] Jul 14 18:10:49 chef pppoe[1855]: Timeout waiting for PADO packets Jul 14 18:10:49 chef pppd[1853]: Exit. Jul 14 18:10:51 chef pppd[1941]: sent [LCP ConfReq id=0x1 ] Jul 14 18:11:06 chef pppd[1941]: LCP: timeout sending Config-Requests Jul 14 18:11:06 chef pppd[1941]: Connection terminated. Jul 14 18:11:06 chef pppd[1941]: Waiting for 1 child processes... Jul 14 18:11:06 chef pppd[1941]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-1878/pppoe-debug.txt-0, pid 1943 Jul 14 18:11:10 chef pppoe[1943]: Timeout waiting for PADO packets Jul 14 18:11:10 chef pppd[1941]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-1878/pppoe-debug.txt-0 finished (pid 1943), status = 0x100 Jul 14 18:11:10 chef pppd[1941]: Exit. Jul 14 18:38:15 meister kernel: registered device ppp0 Jul 14 18:38:15 meister pppd[607]: pppd 2.3.11 started by root, uid 0 Jul 14 18:38:15 meister pppd[607]: Using interface ppp0 Jul 14 18:38:15 meister pppd[607]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 18:38:47 meister pppd[607]: LCP: timeout sending Config-Requests Jul 14 18:38:47 meister pppd[607]: Connection terminated. Jul 14 18:38:51 meister pppoe[611]: Timeout waiting for PADO packets Jul 14 18:38:51 meister pppd[607]: Exit. Jul 14 18:38:56 meister pppd[670]: pppd 2.3.11 started by root, uid 0 Jul 14 18:38:56 meister pppd[670]: Using interface ppp0 Jul 14 18:38:56 meister pppd[670]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 18:39:27 meister pppd[670]: LCP: timeout sending Config-Requests Jul 14 18:39:27 meister pppd[670]: Connection terminated. Jul 14 18:39:31 meister pppoe[672]: Timeout waiting for PADO packets Jul 14 18:39:31 meister pppd[670]: Exit. Jul 14 18:39:36 meister pppd[779]: pppd 2.3.11 started by root, uid 0 Jul 14 18:39:36 meister pppd[779]: Using interface ppp0 Jul 14 18:39:36 meister pppd[779]: Connect: ppp0 <--> /dev/ttyp2 Jul 14 18:39:37 meister pppd[779]: sent [LCP ConfReq id=0x1 ] Jul 14 18:40:07 meister pppd[779]: LCP: timeout sending Config-Requests Jul 14 18:40:07 meister pppd[779]: Connection terminated. Jul 14 18:40:07 meister pppd[779]: Waiting for 1 child processes... Jul 14 18:40:07 meister pppd[779]: script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-718/pppoe-debug.txt-0, pid 781 Jul 14 18:40:11 meister pppoe[781]: Timeout waiting for PADO packets Jul 14 18:40:11 meister pppd[779]: Script /usr/sbin/pppoe -p /var/run/-adsl.pid.pppoe -I eth1 -T 80 -U -m 1412 -D /tmp/pppoe-debug-718/pppoe-debug.txt-0 finished (pid 781), status = 0x100 Jul 14 18:40:11 meister pppd[779]: Exit. Sat Jul 14 18:40:13 CEST 2001 --------------------------------------------- * The following section is a dump of the packets * sent and received by rp-pppoe. If you don't see * any output, it's an Ethernet driver problem. If you only * see three PADI packets and nothing else, check your cables * and modem. Make sure the modem lights flash when you try * to connect. Check that your Ethernet card is in * half-duplex, 10Mb/s mode. If all else fails, * try using pppoe-sniff. rp-pppoe debugging dump rp-pppoe-3.1 18:39:36.335 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12 SourceAddr 00:80:48:c3:43:18 DestAddr ff:ff:ff:ff:ff:ff 01 01 00 00 01 03 00 04 0d 03 00 00 ............ 18:39:41.328 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12 SourceAddr 00:80:48:c3:43:18 DestAddr ff:ff:ff:ff:ff:ff 01 01 00 00 01 03 00 04 0d 03 00 00 ............ 18:39:51.328 SENT PPPoE Discovery (8863) PADI sess-id 0 length 12 SourceAddr 00:80:48:c3:43:18 DestAddr ff:ff:ff:ff:ff:ff 01 01 00 00 01 03 00 04 0d 03 00 00 ............